Merge pull request #12 from amberisvibin/hardware.inc

Setup hardware.inc

code/boot/.editorconfig

@@ -8,7 +8,7 @@ charset = utf-8
 trim_trailing_whitespace = true
 insert_final_newline = true
 
-[*.s]
+[*.{s,inc}]
 indent_style = space
 indent_size = 2
 

code/boot/src/boot.s

@@ -10,28 +10,28 @@
 ;;
 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
-  ORG $8000
+  ORG ROM_BASE
 
 RESET
-  lda %11000001 ; 8n1 serial, enable DLAB
+  lda #%11000001 ; 8n1 serial, enable DLAB
   sta UART_LCR
 
-  lda $00       ; Set divisor to 12 (9600 baud)
+  lda #$00       ; Set divisor to 12 (9600 baud)
   sta UART_DLL
-  lda $0C
+  lda #$0C
   sta UART_DLM
 
-  lda %11000000 ; 8n1 serial, disable DLAB
+  lda #%11000000 ; 8n1 serial, disable DLAB
   sta UART_LCR
 
-  lda %01000000 ; Enable RTS
+  lda #%01000000 ; Enable RTS
   sta UART_MCR
 
-  lda 'H        ; send 'H'
+  lda 'H         ; send 'H'
   sta UART_BUFR
 
 WAIT
-  sync          ; Wait for interrupts
+  sync           ; Wait for interrupts
   nop
   bra WAIT
 
@@ -41,7 +41,7 @@ WAIT
 ;;
 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
-  ORG $FFF0
+  ORG VECS_BASE
 
 VECTORS
   fdb $0000 ; Reserved

code/boot/src/hardware.inc

@@ -8,7 +8,10 @@
 ;;
 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
+SRAM_BASE EQU $0000 ; SRAM Base Address
 UART_BASE EQU $7F00 ; UART Base Address
+ROM_BASE  EQU $8000 ; ROM Base Address and Entry Point
+VECS_BASE EQU $FFF0 ; Vectors Base Address
 
 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 ;;
@@ -16,15 +19,18 @@ UART_BASE EQU $7F00 ; UART Base Address
 ;;
 ;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;;
 
-; When UARTF_DLAB = 0:
+; When UARTF_LCR_DLAB = 0:
 UART_BUFR EQU UART_BASE    ; TX/RX Buffer (Read for RX, Write for TX)
+UART_RBR EQU UART_BASE     ; RX Buffer Register
+UART_THR EQU UART_BASE     ; TX Holding Register
 UART_IER EQU UART_BASE + 1 ; Interrupt Enable Register
-UART_IIR EQU UART_BASE + 1 ; Interrupt Ident Register (Upon Read)
 
-; When UARTF_DLAB = 1:
+; When UARTF_LCR_DLAB = 1:
 UART_DLL EQU UART_BASE     ; Divisor Latch (LSB)
 UART_DLM EQU UART_BASE + 1 ; Divisor Latch (MSB)
 
+; Independent of DLAB:
+UART_IIR EQU UART_BASE + 2 ; Interrupt Ident Register (Upon Read)
 UART_FCR EQU UART_BASE + 2 ; FIFO Control Register (Upon Write)
 UART_LCR EQU UART_BASE + 3 ; Line Control Register
 UART_MCR EQU UART_BASE + 4 ; MODEM Control Register
@@ -32,5 +38,59 @@ UART_LSR EQU UART_BASE + 5 ; Line Status Register
 UART_MSR EQU UART_BASE + 6 ; MODEM Status Register
 UART_SCR EQU UART_BASE + 7 ; Scratch Register (Not for control just spare RAM)
 
-; UART Flags
+; UART Flags for Interrupt Enable Register:
-UARTF_DLAB EQU %00000001
+UARTF_IER_ERBFI EQU %10000000 ; Enable Received Data Available Interrupt
+UARTF_IER_ETBEI EQU %01000000 ; Enable Transmitter Holding Register Empty Interrupt
+UARTF_IER_ELSI  EQU %00100000 ; Enable Receiver Line Status Interrupt
+UARTF_IER_EDSSI EQU %00010000 ; Enable MODEM Status Interrupt
+
+; UART Flags for FIFO Control Register:
+UARTF_FCR_FE   EQU %10000000 ; FIFO Enabled
+UARTF_FCR_RFR  EQU %01000000 ; RCVR FIFO Reset
+UARTF_FCR_XFR  EQU %00100000 ; XMIT FIFO Reset
+UARTF_FCR_DMS  EQU %00010000 ; DMA Mode Select
+UARTF_FCR_RTL  EQU %00000010 ; RCVR Trigger (LSB)
+UARTF_FCR_RTM  EQU %00000001 ; RCVR Trigger (MSB)
+
+; UART Flags for Interrupt Ident Register:
+UARTF_IIR_INP  EQU %10000000 ; Reset if Interrupt Pending; 'INP' = Interrupt Not Pending
+UARTF_IIR_IIDM EQU %01110000 ; Interrupt ID Mask
+UARTF_IIR_FEM  EQU %00000011 ; FIFOs Enabled Mask
+
+; UART Flags for Line Control Register:
+UARTF_LCR_WLS  EQU %11000000 ; Word Length Select Bits
+UARTF_LCR_STB  EQU %00100000 ; Stop Bits
+UARTF_LCR_PEN  EQU %00010000 ; Parity Enable
+UARTF_LCR_EPS  EQU %00001000 ; Even Parity Select
+UARTF_LCR_SPR  EQU %00000100 ; Stick Parity
+UARTF_LCR_BRK  EQU %00000010 ; Set Break
+UARTF_LCR_DLAB EQU %00000001 ; Divisor Latch Access Bit
+
+; UART Flags for MODEM Control Register:
+UARTF_MCR_DTR  EQU %10000000 ; Data Terminal Ready
+UARTF_MCR_RTS  EQU %01000000 ; Enabling Request to Send
+UARTF_MCR_OUT1 EQU %00100000 ; Out 1
+UARTF_MCR_OUT2 EQU %00010000 ; Out 2
+UARTF_MCR_LOOP EQU %00001000 ; Loop
+
+; UART Flags for Line Status Register:
+UARTF_LSR_DR   EQU %10000000 ; Data Ready
+UARTF_LSR_OE   EQU %01000000 ; Overrun Error
+UARTF_LSR_PE   EQU %00100000 ; Parity Error
+UARTF_LSR_FE   EQU %00010000 ; Framing Error
+UARTF_LSR_BI   EQU %00001000 ; Break Interrupt
+UARTF_LSR_THRE EQU %00000100 ; Transmitter Holding Register
+UARTF_LSR_TEMT EQU %00000010 ; Transmitter Empty
+UARTF_LSR_FIFO EQU %00000001 ; Error in RCVR FIFO
+
+; UART Flags for MODEM Status Register:
+UARTF_MSR_DCTS EQU %10000000 ; Delta Clear to Send
+UARTF_MSR_DDSR EQU %01000000 ; Delta Data Set Ready
+UARTF_MSR_TERI EQU %00100000 ; Trailing Edge Ring Indicator
+UARTF_MSR_DDCD EQU %00010000 ; Delta Data Carrier Detect
+UARTF_MSR_CTS  EQU %00001000 ; Clear To Send
+UARTF_MSR_DSR  EQU %00000100 ; Data Set Ready
+UARTF_MSR_RI   EQU %00000010 ; Ring Indicator
+UARTF_MSR_DCD  EQU %00000001 ; Data Carrier Detect
+
+; vim: ft=asm